How to connect a universal remote to a TV :

1. Manually turn on the device (TV, VCR, DVD, etc.) you wish to program.

2. Press and hold the CODE SEARCH/SETUP button on the remote until the INDICATOR LIGHT lights, then release.

3. Press and release the button for the device you are programming (TV, VCR, DVD, etc.). For AUX, press AUX then the device Button you are assigning to AUX. The INDICATOR LIGHT will blink then remain lit.

4. Enter the three or four digit code for your device using the number buttons in the GE Universal Remote. After your code is entered the INDICATOR LIGHT will turn off.

5. Aim the remote at the device (TV, VCR, DVD, etc.) and press the POWER button. Your device should turn off.

Note:  If your device does not respond to the first code listed, If your TV, VCR, DVD, etc. does not respond after you have tried all the codes for your brand or if your brand is not listed, try searching for your codes by  following the steps below.

1.Turn on the device you wish to program.

2.LIGHT lights, then release. Press and hold CODE SEARCH/SETUP until the INDICATOR

3.programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will blink once then remain lit. For AUX, press AUX then the device

button you are assigning to AUX. Press and release the device button for the device you are

4. 2 seconds between each time you press POWER. Important: You may have to press POWER up to 250 times.Press and release POWER until your device turns off. Wait at least

5.INDICATOR LIGHT will go off.

When your device turns off press the ENTER/SAVE button. The SLEEP FEATURE (RM94902, RM94904 and RM94905) This feature will turn off your TV at the time you choose from 1-99 minutes.

To Use the Sleep Feature:

1. Press and hold the SLEEP button until the INDICATOR LIGHT stays lit.

2. Enter time in minutes using the numerical keypad. (Minutes 1-99;press 0 before the actual number).

3. Lease remote aimed at television. The Sleep Function will not function properly unless the remote is left aimed at the television.

Turn Off the Sleep Feature: 

Press and hold SLEEP until the INDICATOR LIGHT blinks or press the

POWER button to turn off the TV.

Program your remote control to a BOSE Solo Sound Bar, use the following codes:
4001
5042
4017
1961
31629
31229
31841
30639
31253
30674

For programming with Uverse:
Press (at same time) ATT/OK – 955 – Enter
The volume control will then follow the mode button.

For programming with DirecTV:
Slide switch to AV1 or AV2
1. Press and hold MUTE and SELECT (LED flashes twice)
2. Enter the 4 or 5 digit code from above.
After each code, try using the VOL UP and see if VOL works.
If so, slide switch to AV1 or AV2
1. Press and hold MUTE and SELECT (LED flash 2x)
2. 993 then press SELECT
NOTE: Be sure your Bose is set to accept the IR codes.

(Confirmed: works with BOSE Solo Soundbar with SKY HD Rev9, DirecTV RC64, and Xfinity remotes)

To program your remote control to a INSIGNIA Sound Bar, use the following codes:
21268
12002
10463

If using Comcast remote and above codes do not work, try Code Search:
Turn on your sound bar.
Press Aux once on remote.
Then press and hold Setup until the key blinks 2x, then release Setup.
Enter 9 – 9 – 3.
The Aux key will blink 2x.
Press Power and aim the remote control at the sound bar and press CH + one or more times until the sound bar turns off.
Press Setup once to lock in the code.
The Aux key will blink twice.
To search for the codes of another device, repeat steps 1 to 5, but substitute the mode key for the device you are searching for.
SIDE NOTE: In search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.

(Confirmed: works with INSIGNIA Soundbar NS-SBAR-A, NS-SB314, SB212, with Comcast remotes)

To program your remote control to a SAMSUNG Sound Bar, use the following codes:
32609
22609
21014
20045

(Confirmed: works with Samsung Soundbar HW-FM55C, FM550, HW-HM45 and Xfinity remotes)

To program your remote control to a SONY Sound Bar, use the following codes:
1345
4029
31759

With Uverse remote try programming this method:
Program = press ATT/OK at same time – 955 – Enter.
In ATT mode set the STB sound to 15.
Set TV sound to a comfortable level
Set SONY soundbar sound to a comfortable level.

(Confirmed: works with SONY Soundbar HTCT260, CT770, CT-660, HTCT660 and Uverse remotes)

To program your remote control to an LG Sound Bar, use the following codes:
32676
11993
31953
31293

(Confirmed: works with LG Soundbar NB2022, NB3530A and Xfinity XR2 remote – Xfinity XR5 v4 remote)

To program your remote control to a VIZIO Sound Bar, use the following codes:
0883
0660
1517
1144
31517
11144
31975

Vizio Subwoofer volume control:
00105 Sub Down
00040 Sub Up

(Confirmed: works with VIZIO Soundbar VSB200, SB4020M-AO, SB15 2.1, VHT215, SB4021M-A1, VSB202, VSB210, VSB200-B)

Step-by-step for getting your Vizio Soundbar to work with the Comcast remote using EFC codes:
Aux – Setup (2 blinks) – 11144 (2 blinks)
Aux – Setup (2 blinks) – 994 – Setup – 001690 – Vol Up – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001680 – Vol Down – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 000370 – Mute – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001650 – Power – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001640 – Input – 2 blinks

For Comcast remote, follow the Unlock/Lock directions using the 993 code to make the AUX Volume mode control the sound bar. 
Make sure you unlock the volume with the 993 code following the instructions.
The Comcast remote will then control the volume via the sound bar and not the TV.

To program your remote control to a SANYO Sound Bar, use the following codes:
20047
10154
10159
10051
10250

When connecting the Sound Bar, you can plug your soundbar directly into the Cable box, SAT box, or TV. Different programming methods may be needed depending on how your soundbar is connected.

Sanyo 4 Digit Blu Ray Player Remote Codes:
0742
0667
0705
0718
0735
2495
0095
0405
2205
2215
2225
2235
2245
2645
3945

Program your universal remote control to a Sanyo DVD player. Use the following remote codes.

Sanyo DVD Player 4 Digit Remote Control Codes:
0670
0695
0790
1919
0873
0896
2050
2393

Program your universal remote control to an Sanyo Sound Bar. Use the following 3 and 5 digit remote codes.

Sanyo Soundbar 3 Digit Remote Control Codes:
590
611
627
661
683

Sanyo Soundbar 5 Digit Remote Control Codes:
20047
10154
10159
10051
10250
20035
30189
30531
20081
21593
20593
20000
20039
20149
21781

The above codes have shown to work with Sanyo soundbar models FWSB415E, FWSB405FS, FW405SB, and FWSB405F.

If these remote codes do not work, try the code search on your CAB or SAT remote…

ATT Remote RC7X:
Program your Sanyo soundbar to the RC7x remote control:
Follow the instructions by going to…
-MENU
-SETTINGS
-SETTINGS & HELP
-REMOTE CONTROL
-AUDIO DEVICE

With DIRECTV or ATT as your cable with DIRECTV Remote Control:
-Sanyo Soundbar on
-Volume up but muted
-AV1 or AV2
-Press and hold MUTE and SELECT for 2 blinks
-Enter 9 9 1 and wait 2 blinks
-Enter 3
-Press and release VOL UP
-Point the remote at the Sanyo soundbar and keep pressing and releasing the CH UP key
-When the volume changes, press select to lock in code.

If DIRECTV remote controls the power of the Sanyo soundbar but not volume, try this:
-AV1 or AV2
-Press and hold MUTE & SELECT
-Wait for 2 blinks and release
-Enter 9 9 3
-Press SELECT

Code Search using silver Comcast remote with a red OK/Select button:
-Turn on your Sanyo sound bar
-Press Aux once
-Press and hold Setup until the key blinks twice
-Release Setup
-Enter 9 9 1 3
-The Aux key will blink twice
-Press Power and aim the remote control at the Sanyo sound bar
-Press CH+ until the sound bar turns off
NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device.
-Press Setup once to lock in the code
-The Aux key will blink twice

With a Comcast Xfinity remote with the red ok button:
-Press aux then press and hold setup till it blinks twice
-Enter code from list above
(This code will control the volume)

With a Comcast Xfinity remote with the red ok button – To lock to the Sanyo soundbar:
-Hold setup till it blinks twice
-Enter 9 9 3
-Press aux
To take the lock off and make it independent of each device:
-Hold setup till it blinks twice
-Press 993 then vol+ once
(Now you can select each device you want to change the volume for)

The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Sanyo soundbar.

SONY 3 & 4 digit universal codes are:
002, 000, 011, 080, 111, 006, 071, 128, 1904, 925
0000, 0834, 0810, 1685, 1786, 1032, 1972

Universal Remote Control Codes For Sanyo TVs

Goto :  Sanyo DVD , Sanyo Sound Bar , Sanyo Blu-Ray 

The universal code for most is 049 for a Sanyo TV.

1. With your universal remote you press the code search key until it illuminates and then you press and release the TV key.

2. Next enter the three digit code (3 digit remote code page) and the indicator light turns off. 

3. If you enter in the wrong code the light will flash rapidly.

4. Aim the remote at your tv and press the on/off key.

5. If your tv turns off then you have found the right code!

Sanyo TV Remote Codes

use these codes for your Sanyo TV : 054, 069, 023, 025.

If those do not work then also try: 004, 013, 049, 108, 110, 180, 209

Codes for Sanyo TV using Sony Remote 

• 330,335

Codes for Sanyo TV using Comcast xfinity remote

• 10154, 10159

Codes for Sanyo TV using Cox remote

• 0054, 0154, 0088, 0799, 1142

Codes for SANYO TV using one for all remote

• 0049 0097 0110 0004 0268 0012 0108 0180

Codes for SANYO TV using one for  using DirecTV remote - 

• 10154, 10088, 10107, 10146,
•   10159, 10232, 10484, 10799,
•   10893, 11142, 10208, 10339

Sanyo Soundbar Remote Control Codes

Make sure to hookup and power on all the Sony TV or other device you want to setup using Sony universal remote codes. next, make sure the batteries are working in the universal remote. Note down the Sony universal remote codes from the list provided. Nothing is more frustrating to find out that you have not hooked up or universal remote batteries are bad after spending your evening on trying to program Sony universal remote.

Sony Programming Instructions

Follow these steps to program the remote control.

Step 1

Turn on the component to be programmed.

Step 2

On the remote control, press and hold the SET button until the SET indicator lights up.

Step 3

Press the appropriate component select button for the component being set up.

Step 4

Using the number pad, enter the component's manufacturer code. Note: If more than one code number is listed for the manufacturer, repeat the procedure, entering one code at a time until you find one that works.

Step 5

Press the ENTER button.Point the remote control at the component and press the POWER button.

SONY 3 & 4 digit universal codes are

002, 000, 011, 080, 111, 006, 071, 128, 1904, 925
0000, 0834, 0810, 1685, 1786, 1032, 1972

VCR Codes

Sony – 301,302,303

Admiral (M. Ward) – 327
Aiwa – 338,344
Audio Dynamic – 314,337
Broksonic – 319,317
Canon – 309,308
Citizen – 332
Craig – 302,332
Criterion – 315
Curtis Mathis – 304,338,309
Daewoo – 341,312,309

DBX – 314,336,337
Dimensia – 304
Emerson – 319,320,316,317,318,341
Fisher – 330,335
Funai – 338
General Electric 329,304,309
Go Video – 322,339,340
Goldstar – 332
Hitachi – 306,304,305,338
Memorex – 309,335
Minolta – 305,304
Mitsubishi / MGA – 323,324,325,326
Multitech – 325,338,321
NEC – 314,336,337
Optimus – 327
Panasonic – 308,309,306,307
Pentax – 305,304
Philco – 308,309
Philips – 308,309,310
Pioneer – 308
Quasar – 308,309,306
RCA / Proscan – 304,305,308,309,311,312,313,310,329

Realistic – 309,330,328,335,324,338
Sansui – 314
Samsung – 322,313,321
Sanyo – 330,335
Scott – 312,313,321,335,323,324,325,326
Sharp – 327,328
Sylvania – 308,309,338,310
Symphonic – 338
Tashiro – 332
Tatung – 314,336,337
Teac – 314,336,338,337
Technics – 309,308
Toshiba – 312,311
Wards – 327,328,335,331,332
Yamaha – 314,330,336,337
Zenith – 331

Disc Player Code Numbers:
Sony – 701
Panasonic – 704,710
Pioneer – 702

DVD Code Numbers:
sony dvd remote codes – 751
Panasonic – 753
Pioneer – 752
RCA – 755
Toshiba – 754

Cable Box Code Numbers:
Hamlin/Regal – 222,223,224,225,226
Jerrold/G.I. – 201,202,203,204,205,206,207,208,218
Oak – 227,228,229
Panasonic – 219,220,221
Pioneer – 219,220,221,214,215
Scientific Atlanta – 209,210,211
Tocom – 216,217

Zenith – 212,213

DBS Receiver Code Numbers:
Sony – 801 (Preset code for remote control)
General Electric – 802
Hitachi – 805
Hughes – 804
Panasonic – 803
RCA / Proscan – 802,808
Toshiba – 806,807

Download the Manual

Universal Remote (Replacement for RM-V202) Codes for Model # RM-V210