Program your universal remote control to a JBL Soundbar. Use the following 4 and 5 digit remote codes.

JBL Soundbar 4 Digit Remote Control Codes:
4001
5009
6050

JBL Soundbar 5 Digit Remote Control Codes:
30110
30281
31306
32241

If these remote codes do not work, try the code search on your CAB or SAT remote…

Code Search using Comcast Remote Control:
– Turn on your Soundbar
– Press Aux once
– Press and hold Setup until the key blinks twice
– Release Setup
– Enter 9 9 1 3 or 9 9 3
– The Aux key will blink twice
– Press Power and aim the remote control at the soundbar
– Press CH+ until the soundbar turns off
– In the code search mode, the remote control will send IR codes from its library to the selected device.
– Press Setup once to lock in the code
– The Aux key will blink twice

Code Search using DIRECTV Remote Control:
– Turn Soundbar ON
– Volume up but MUTED
– Press AV1 or AV2
– Press and hold MUTE and SELECT for 2 blinks
– Enter 9 9 1 and wait 2 blinks
– Enter 3
– Press and release VOL UP
– Point the remote at the soundbar and keep pressing and releasing the CH UP key
– When the volume changes, press SELECT to lock in code

The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your JBL soundbar.

 Program your universal remote control to a Klipsch Soundbar. Use the following 3, 4, and 5 digit remote codes.

Universal Remote Codes for Klipsch Sound Bar

Control your Klipsch sound bar models ‎R-10B · ‎RSB-3 · ‎RSB-14 · ‎RSB-11 using the universal remote control, you can control functions such as Volume UP, Volume DOWN, and MUTE. We have listed the most popular remote controls and corresponding universal remote control programming codes for Klipsch sound bar. 

 ATT remote: 5144
 Bright House remote : 048
Charter Cable remote: 31609
Cox Cable remote: 1609
DirecTV: 30531 or 31609
Dish Network: 2652
One For All: 0531 or 1609
RCA: 41609
Suddenlink: 1609
Time Warner Cable: 3489
Verizon Fios: 1050
Xfinity: 30531

For Logitech Harmony Remotes: Ultimate Home, Ultimate, Ultimate One, Touch, Home Control, Smart Control, Ultimate Hub, Home Hub, Smart Keyboard, Harmony One, One +, Harmony 200, 300, 350, 600, 650, 700

Universal Remote Programming instruction for using Klipsch Sound Bar

1. Enter Setup Mode

   Press and hold down the SETUP button on the remote until the red light on the remote turns on. Release the SETUP button. The red light will remain on.

   NOTE: The red light with either be a small light at the top of the remote or the power on/off button.

2. Press the device type button

   Press and release the device button on the remote for the type of device you wish to control. The red light will blink once and remain on.

   NOTE: If there is not a device button on the remote for your type of device, you can use any device button on the remote.

3. Enter the device code

   Use the number buttons on the remote to enter the codes listed above. The red light will turn off after entering the fourth digit.

4. Tests the results

   Point the remote at the device. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device, return to Step 1 above and use the next code in the list.

5. Repeat this process for your other devices

Philips Soundbar 4 Digit Remote Control Codes:
Using a Universal Remote Control? Try the 4 digit codes first…
0729
1798
1805
0296
1216
1296
1116
1316
0216
0177
0083
0983
0084
0184
0277
0377

Philips Soundbar 5 Digit Remote Control Codes:
Using a CAB or SAT Remote Control? Try the 5 digit codes first…
32459
32311
30189
20081
31266
20035
20618
20739
11454
10054
10037
10690
11483

The above codes have shown to work with Philips soundbar models CSS2133B/F7, B5/37 Fidelio, HTL2163B, HTL3110B/F7, HTL2101A/F7, HTL7180/F7, HTL4115B, HTL2101/F7, HTL9100/12, and CSS2123B/F7.

If these remote codes do not work, try the code search on your CAB or SAT remote…

Using Xfinity? Use the remote code 32459 or 32311.
The volume will work with the AUX button but not the power, To fix this…
To make volume buttons work for the Philips soundbar when remote is in CABLE mode:
-Push the TV button once
-Push and hold the Setup button on the remote until the TV button blinks twice
-Then enter 9 9 3 using the number buttons on the remote
-The TV button will blink 2 times
-Press and release the AUX button one time
-The AUX button will then flash 2 times
-Turn your Television speakers OFF or down
-Push the CABLE button one time
NOTE: The volume button will control the volume of the Philips soundbar but not the volume for the Television (The power button will not turn off the Philips soundbar)

Code Search using silver Comcast remote with a red OK/Select button:
-Turn on your Philips soundbar
-Press Aux once
-Press and hold Setup until the key blinks twice
-Release Setup
-Enter 9 9 1 3
-The Aux key will blink twice
-Press Power and aim the remote control at the Philips soundbar
-Press CH+ until the sound bar turns off
NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device.
-Press Setup once to lock in the code
-The Aux key will blink twice

DIRECTV or ATT with DIRECTV Remote Control:
-Turn Philips Soundbar ON
-Volume up but muted
-AV1 or AV2
-Press and hold MUTE and SELECT for 2 blinks
-Enter 9 9 1 and wait 2 blinks
-Enter 3
-Press and release VOL UP
-Point the remote at the Philips soundbar and keep pressing and releasing the CH UP key
-When the volume changes, press SELECT to lock in code.

If DirecTV remote controls the power of the Philips soundbar but not volume, try this:
-AV1 or AV2
-Press and hold MUTE & SELECT
-Wait for 2 blinks and release
-Enter 9 9 3
-Press SELECTcodes, control, philips, remote, sound bar, soundbar, universal

Program your universal remote control to an RCA Sound Bar.
Use the following 5 digit remote codes.

RCA Soundbar 5 Digit Remote Control Codes:
Most likely to work:
20060
31254
30531

Other RCA Soundbar 5 Digit Remote Control Codes to try:
20149
20042
21060
21014
31023
21035
20807
20035
32041
33297
32655
30531
31609
31390
31511
33969
33295
32426
31459
31963
30823
31023
33363
33091
30360

These remote codes are for the RCA RTS7010B, RTS7110B-2, RTS7131B, RTS7340SB, RTS736W, RTD3266, RTS635 soundbars.

Code Search using silver Comcast remote with a red OK/Select button:
-Turn on your RCA sound bar
-Press Aux once
-Press and hold Setup until the key blinks twice
-Release Setup
-Enter 9 9 1 3
-The Aux key will blink twice
-Press Power and aim the remote control at the RCA sound bar
-Press CH+ until the RCA sound bar turns off
NOTE: In the code search mode, the remote control will send IR codes from its library to the device.
-Press Setup once to lock in the code
-The Aux key will blink twice

Program your remote control to a BOSE Solo Sound Bar, use the following codes:
4001
5042
4017
1961
31629
31229
31841
30639
31253
30674

For programming with Uverse:
Press (at same time) ATT/OK – 955 – Enter
The volume control will then follow the mode button.

For programming with DirecTV:
Slide switch to AV1 or AV2
1. Press and hold MUTE and SELECT (LED flashes twice)
2. Enter the 4 or 5 digit code from above.
After each code, try using the VOL UP and see if VOL works.
If so, slide switch to AV1 or AV2
1. Press and hold MUTE and SELECT (LED flash 2x)
2. 993 then press SELECT
NOTE: Be sure your Bose is set to accept the IR codes.

(Confirmed: works with BOSE Solo Soundbar with SKY HD Rev9, DirecTV RC64, and Xfinity remotes)

To program your remote control to a INSIGNIA Sound Bar, use the following codes:
21268
12002
10463

If using Comcast remote and above codes do not work, try Code Search:
Turn on your sound bar.
Press Aux once on remote.
Then press and hold Setup until the key blinks 2x, then release Setup.
Enter 9 – 9 – 3.
The Aux key will blink 2x.
Press Power and aim the remote control at the sound bar and press CH + one or more times until the sound bar turns off.
Press Setup once to lock in the code.
The Aux key will blink twice.
To search for the codes of another device, repeat steps 1 to 5, but substitute the mode key for the device you are searching for.
SIDE NOTE: In search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.

(Confirmed: works with INSIGNIA Soundbar NS-SBAR-A, NS-SB314, SB212, with Comcast remotes)

To program your remote control to a SAMSUNG Sound Bar, use the following codes:
32609
22609
21014
20045

(Confirmed: works with Samsung Soundbar HW-FM55C, FM550, HW-HM45 and Xfinity remotes)

To program your remote control to a SONY Sound Bar, use the following codes:
1345
4029
31759

With Uverse remote try programming this method:
Program = press ATT/OK at same time – 955 – Enter.
In ATT mode set the STB sound to 15.
Set TV sound to a comfortable level
Set SONY soundbar sound to a comfortable level.

(Confirmed: works with SONY Soundbar HTCT260, CT770, CT-660, HTCT660 and Uverse remotes)

To program your remote control to an LG Sound Bar, use the following codes:
32676
11993
31953
31293

(Confirmed: works with LG Soundbar NB2022, NB3530A and Xfinity XR2 remote – Xfinity XR5 v4 remote)

To program your remote control to a VIZIO Sound Bar, use the following codes:
0883
0660
1517
1144
31517
11144
31975

Vizio Subwoofer volume control:
00105 Sub Down
00040 Sub Up

(Confirmed: works with VIZIO Soundbar VSB200, SB4020M-AO, SB15 2.1, VHT215, SB4021M-A1, VSB202, VSB210, VSB200-B)

Step-by-step for getting your Vizio Soundbar to work with the Comcast remote using EFC codes:
Aux – Setup (2 blinks) – 11144 (2 blinks)
Aux – Setup (2 blinks) – 994 – Setup – 001690 – Vol Up – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001680 – Vol Down – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 000370 – Mute – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001650 – Power – 2 blinks
Aux – Setup (2 blinks) – 994 – Setup – 001640 – Input – 2 blinks

For Comcast remote, follow the Unlock/Lock directions using the 993 code to make the AUX Volume mode control the sound bar. 
Make sure you unlock the volume with the 993 code following the instructions.
The Comcast remote will then control the volume via the sound bar and not the TV.

To program your remote control to a SANYO Sound Bar, use the following codes:
20047
10154
10159
10051
10250

When connecting the Sound Bar, you can plug your soundbar directly into the Cable box, SAT box, or TV. Different programming methods may be needed depending on how your soundbar is connected.

Program your universal remote control to an Sanyo Sound Bar. Use the following 3 and 5 digit remote codes.

Sanyo Soundbar 3 Digit Remote Control Codes:
590
611
627
661
683

Sanyo Soundbar 5 Digit Remote Control Codes:
20047
10154
10159
10051
10250
20035
30189
30531
20081
21593
20593
20000
20039
20149
21781

The above codes have shown to work with Sanyo soundbar models FWSB415E, FWSB405FS, FW405SB, and FWSB405F.

If these remote codes do not work, try the code search on your CAB or SAT remote…

ATT Remote RC7X:
Program your Sanyo soundbar to the RC7x remote control:
Follow the instructions by going to…
-MENU
-SETTINGS
-SETTINGS & HELP
-REMOTE CONTROL
-AUDIO DEVICE

With DIRECTV or ATT as your cable with DIRECTV Remote Control:
-Sanyo Soundbar on
-Volume up but muted
-AV1 or AV2
-Press and hold MUTE and SELECT for 2 blinks
-Enter 9 9 1 and wait 2 blinks
-Enter 3
-Press and release VOL UP
-Point the remote at the Sanyo soundbar and keep pressing and releasing the CH UP key
-When the volume changes, press select to lock in code.

If DIRECTV remote controls the power of the Sanyo soundbar but not volume, try this:
-AV1 or AV2
-Press and hold MUTE & SELECT
-Wait for 2 blinks and release
-Enter 9 9 3
-Press SELECT

Code Search using silver Comcast remote with a red OK/Select button:
-Turn on your Sanyo sound bar
-Press Aux once
-Press and hold Setup until the key blinks twice
-Release Setup
-Enter 9 9 1 3
-The Aux key will blink twice
-Press Power and aim the remote control at the Sanyo sound bar
-Press CH+ until the sound bar turns off
NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device.
-Press Setup once to lock in the code
-The Aux key will blink twice

With a Comcast Xfinity remote with the red ok button:
-Press aux then press and hold setup till it blinks twice
-Enter code from list above
(This code will control the volume)

With a Comcast Xfinity remote with the red ok button – To lock to the Sanyo soundbar:
-Hold setup till it blinks twice
-Enter 9 9 3
-Press aux
To take the lock off and make it independent of each device:
-Hold setup till it blinks twice
-Press 993 then vol+ once
(Now you can select each device you want to change the volume for)

The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Sanyo soundbar.

Program your universal remote control to an Sceptre Soundbar.Use the following 5 digit remote codes.Sceptre Soundbar 5 Digit Remote Control Codes:1000010878112171136011599If these remote codes do not work, try the code search on your CAB or SAT remote…Code Search using Comcast Remote Control:– Turn on your Soundbar– Press Aux once– Press and hold Setup until the key blinks twice– Release Setup– Enter 9 9 1 3 or 9 9 3– The Aux key will blink twice– Press Power and aim the remote control at the soundbar– Press CH+ until the soundbar turns off– In the code search mode, the remote control will send IR codes from its library to the selected device.– Press Setup once to lock in the code– The Aux key will blink twiceCode Search using DIRECTV Remote Control:– Turn Soundbar ON– Volume up but MUTED– Press AV1 or AV2– Press and hold MUTE and SELECT for 2 blinks– Enter 9 9 1 and wait 2 blinks– Enter 3– Press and release VOL UP– Point the remote at the soundbar and keep pressing and releasing the CH UP key– When the volume changes, press SELECT to lock in codeThe above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Sceptre soundbar.