Complete list of codes for Magnavox Universal Remote Codes for TVs, DVD and audio video devices along with programming instruction to control all your devices.Magnavox Universal Remote Control Programming Codes are used to program your Magnavox remote or any universal remote to conrol your Television and audio video devices.
How to program Remote Control Codes For Magnavox TVs using most universal remote controls
Step 1:
Turn on the TV, Make sure battries are working in the remote.
Step 2:
Press and hold the TV and SEL buttons simultaneously for 3 seconds. The button will light.
Step 3:
With the button lit, point the remote at the TV and enter the TV’s 3, 4, or 5 digit code,choose corresponding code from the list give below.
Step 4:
Verify by pressing the VOLUME + button. This should turn the TV VOLUME up.
Step 5:
Press the TV button to store the 3, 4, or 5 digit code. The button will blink twice to confirm the code is stored.
Program your universal remote control to a Yamaha Sound Bar. Use the following 5 digit remote codes.
Yamaha Sound Bar 5 Digit Remote Control Codes: 31947 31331 30176 31176 30354 10030 10797 10017 10019
All codes reported working with these Yamaha Sound Bar Models:ATS-1030, YSP-1000, YSP-5100, YSP-4100, YSP-1400, YAS-101, YAS-103, YHT-S400, and YSP-4000BL.
These codes have been tested with the….Comcast remote controls, Xfinity XR5, DVR 3 device remote, XR2 Remote, Xfinity XR2 U2, XR2 R2, DirecTV, Directv HR24 STB, S10-S4, U-verse remote control, RC65, Satellite H20 Receiver, DirecTV Plus HD DVR, Comcast 3-in-1 remote, and 1067BG3.
If using Xfinity try these programming methods: -Hold Setup (2 button flashes) -994 -Setup -00169 -Vol Up (2 button flashes) (Programs the volume down button to toggle TVOL on the Yamaha sound bar)
OR
-Hold Setup (2 button flashes) -11144 (2 button flashes) (Accepted by the Xfinity remote and programs the volume down button to toggle TVOL on the Yamaha sound bar, Should let you turn TVOL ON and OFF)
If using U-verse or DirecTV (ATT) try these programming methods: -ATT/OK-955-AUX-ENTER -ATT/OK-977-AUX-TV-ATT-ENTER
OR
Use code 30176 or 31331 for the Yamaha Sound bar (There has to be a TV code programmed to the TV device or the volume keys will not work) Then try this: -AV1 or AV2 -Press and hold MUTE & SELECT, wait for two blinks and release -Enter 30176 Then… -AV1 or AV2 -Press and hold MUTE & SELECT, wait for two blinks and release -Enter 993 -Press SELECT Then… -AV1 or AV2 -Press and hold MUTE & SELECT, wait for two blinks and release -Enter 963 -Press Ch Down Then teach the Yamaha Sound bar the commands from the DirecTV ATT remote control.
OR
Use code 30176 or 31331 for the Yamaha Sound bar (There has to be a TV code programmed to the TV device or the volume keys will not work) -AV1 or AV2 -Press and hold MUTE & SELECT for 2 blinks -Enter 993 -Press SELECT
Program Dish Remote to Pyle Sound Bar How to setup the TV remote to control the Pyle soundbar
Pyle Code Search using DIRECTV Remote Control: – Turn Pyle Soundbar ON – Volume up but MUTED – Press AV1 or AV2 – Press and hold MUTE and SELECT for 2 blinks – Enter 9 9 1 and wait 2 blinks – Enter 3 – Press and release VOL UP – Point the remote at the soundbar and keep pressing and releasing the CH UP key – When the volume changes, press SELECT to lock in code.
Pyle Code Search using Comcast Remote Control: – Turn on your Pyle Soundbar to be programmed. – Press and hold the “Setup” button on your remote. (LED changes from red to green) – Type in the remote code listed above using the number buttons. – If the code is accepted the status LED will blink green twice. (If it blinks red the code was not entered correctly) – Use the remote to operate your Denon soundbar. – Try another code and repeat if the code you entered was not correct.
The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Pyle soundbar.
Your Pyle soundbar should be able to be programmed to use the same IR code your TV does. Read the manual for your Pyle soundbar.
If these remote codes do not work, try the code search on your CAB or SAT remote…
Code Search using Comcast Remote Control: – Turn on your Soundbar – Press Aux once – Press and hold Setup until the key blinks twice – Release Setup – Enter 9 9 1 3 or 9 9 3 – The Aux key will blink twice – Press Power and aim the remote control at the soundbar – Press CH+ until the soundbar turns off – In the code search mode, the remote control will send IR codes from its library to the selected device. – Press Setup once to lock in the code – The Aux key will blink twice
Code Search using DIRECTV Remote Control: – Turn Soundbar ON – Volume up but MUTED – Press AV1 or AV2 – Press and hold MUTE and SELECT for 2 blinks – Enter 9 9 1 and wait 2 blinks – Enter 3 – Press and release VOL UP – Point the remote at the soundbar and keep pressing and releasing the CH UP key – When the volume changes, press SELECT to lock in code
The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your JBL soundbar.
Program your universal remote control to a Klipsch Soundbar. Use the following 3, 4, and 5 digit remote codes.
Universal Remote Codes for Klipsch Sound Bar
Control your Klipsch sound bar models R-10B · RSB-3 · RSB-14 · RSB-11 using the universal remote control, you can control functions such as Volume UP, Volume DOWN, and MUTE. We have listed the most popular remote controls and corresponding universal remote control programming codes for Klipsch sound bar.
ATT remote: 5144 Bright House remote : 048 Charter Cable remote: 31609 Cox Cable remote: 1609 DirecTV: 30531 or 31609 Dish Network: 2652 One For All: 0531 or 1609 RCA: 41609 Suddenlink: 1609 Time Warner Cable: 3489 Verizon Fios: 1050 Xfinity: 30531
For Logitech Harmony Remotes: Ultimate Home, Ultimate, Ultimate One, Touch, Home Control, Smart Control, Ultimate Hub, Home Hub, Smart Keyboard, Harmony One, One +, Harmony 200, 300, 350, 600, 650, 700
Universal Remote Programming instruction for using Klipsch Sound Bar
Enter Setup Mode
Press and hold down the SETUP button on the remote until the red light on the remote turns on. Release the SETUP button. The red light will remain on.
NOTE: The red light with either be a small light at the top of the remote or the power on/off button.
Press the device type button
Press and release the device button on the remote for the type of device you wish to control. The red light will blink once and remain on.
NOTE: If there is not a device button on the remote for your type of device, you can use any device button on the remote.
Enter the device code
Use the number buttons on the remote to enter the codes listed above. The red light will turn off after entering the fourth digit.
Tests the results
Point the remote at the device. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device, return to Step 1 above and use the next code in the list.
Vizio Sound Bar 4 Digit Remote Control Codes: 1517 0660 0883
Vizio Sound Bar 5 Digit Remote Control Codes: 31517 32454 31975 11144
Some sound bars can be programmed to accept other IR to control them. Apply the TV volume IR into the Vizio SB.
All codes reported working with the Vizio Soundbar VSB200, SB3820, VSB201, VHT215, S3821. These codes have been tested with the Comcast remote controls, Verizon Fios, Xfinity X5 remote, Uverse, U-Verse, S10-S3, S10-S4, Atlas 1056B03, etc.
If you use Verizon Fios, there is a Key Fix. If your remote control is programmed for your TV, but the VOL, Mute, or the A/V keys do not work correctly, then you can try using the Key Fix feature to fix the buttons. Here is how to: 1 – Press and hold the OK and * buttons at same time. The Red LED will blink twice and then stay illuminated. 2 – Press and hold the key that does not work properly. The remote control will auto try a new code every 1 sec. 3 – When the TV responds correctly then release the key. 4 – Then press OK to save the current setting.
Some remote codes may not work with certain configurations such as cable TV remote model or sat TV remote. If this is the case, you can program an unsupported device (such as a sound bar) by setting each key individually to send a code. This means each button or key on your remote will need to be programmed for the remote to work. Each remote function works by sending a code to sound bar. This is done by setting AUX to a main device code and then setting things like volume up and down individually. An example would be… The code 00169 will make the volume go up. The code 00168 will make the volume go down. The code 00037 will toggle the mute. The code 00165 will turn the power on and off.
If you use Comcast, here is a way to make the remote work with the SB. 1 – Check to see if the signals work by assigning 20752 to the AUX button. 2 – Vol DOWN should make the volume go down, and the right arrow should make it go up. 3 – If the signals work then you can permanently assign the EFC 00169 to Vol UP and 00168 to Vol DOWN by using the 994 Command.
Here is a Vizio sound bar and Uverse remote control fix… 1 – Program the Vizio sound bar to “TV” key on the Uverse remote using code 1009. 2 – Program your TV to the “DVD” key on remote using manual code or auto scan mode. 3 – Send volume to TV button, press ATT then press OK, then enter 955, then press TV button. 4 – If you want to power all off at once, press ATT and OK buttons, release, enter 977, press ATT again, then press DVD and TV buttons, then the ENTER button. When you press volume the sound bar will operate, then when you press power everything should power off or on.
Philips Soundbar 4 Digit Remote Control Codes: Using a Universal Remote Control? Try the 4 digit codes first… 0729 1798 1805 0296 1216 1296 1116 1316 0216 0177 0083 0983 0084 0184 0277 0377
Philips Soundbar 5 Digit Remote Control Codes: Using a CAB or SAT Remote Control? Try the 5 digit codes first… 32459 32311 30189 20081 31266 20035 20618 20739 11454 10054 10037 10690 11483
The above codes have shown to work with Philips soundbar models CSS2133B/F7, B5/37 Fidelio, HTL2163B, HTL3110B/F7, HTL2101A/F7, HTL7180/F7, HTL4115B, HTL2101/F7, HTL9100/12, and CSS2123B/F7.
If these remote codes do not work, try the code search on your CAB or SAT remote…
Using Xfinity? Use the remote code 32459 or 32311. The volume will work with the AUX button but not the power, To fix this… To make volume buttons work for the Philips soundbar when remote is in CABLE mode: -Push the TV button once -Push and hold the Setup button on the remote until the TV button blinks twice -Then enter 9 9 3 using the number buttons on the remote -The TV button will blink 2 times -Press and release the AUX button one time -The AUX button will then flash 2 times -Turn your Television speakers OFF or down -Push the CABLE button one time NOTE: The volume button will control the volume of the Philips soundbar but not the volume for the Television (The power button will not turn off the Philips soundbar)
Code Search using silver Comcast remote with a red OK/Select button: -Turn on your Philips soundbar -Press Aux once -Press and hold Setup until the key blinks twice -Release Setup -Enter 9 9 1 3 -The Aux key will blink twice -Press Power and aim the remote control at the Philips soundbar -Press CH+ until the sound bar turns off NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device. -Press Setup once to lock in the code -The Aux key will blink twice
DIRECTV or ATT with DIRECTV Remote Control: -Turn Philips Soundbar ON -Volume up but muted -AV1 or AV2 -Press and hold MUTE and SELECT for 2 blinks -Enter 9 9 1 and wait 2 blinks -Enter 3 -Press and release VOL UP -Point the remote at the Philips soundbar and keep pressing and releasing the CH UP key -When the volume changes, press SELECT to lock in code.
If DirecTV remote controls the power of the Philips soundbar but not volume, try this: -AV1 or AV2 -Press and hold MUTE & SELECT -Wait for 2 blinks and release -Enter 9 9 3 -Press SELECTcodes, control, philips, remote, sound bar, soundbar, universal
These remote codes are for the RCA RTS7010B, RTS7110B-2, RTS7131B, RTS7340SB, RTS736W, RTD3266, RTS635 soundbars.
Code Search using silver Comcast remote with a red OK/Select button: -Turn on your RCA sound bar -Press Aux once -Press and hold Setup until the key blinks twice -Release Setup -Enter 9 9 1 3 -The Aux key will blink twice -Press Power and aim the remote control at the RCA sound bar -Press CH+ until the RCA sound bar turns off NOTE: In the code search mode, the remote control will send IR codes from its library to the device. -Press Setup once to lock in the code -The Aux key will blink twice
Program your remote control to a BOSE Solo Sound Bar, use the following codes: 4001 5042 4017 1961 31629 31229 31841 30639 31253 30674
For programming with Uverse: Press (at same time) ATT/OK – 955 – Enter The volume control will then follow the mode button.
For programming with DirecTV: Slide switch to AV1 or AV2 1. Press and hold MUTE and SELECT (LED flashes twice) 2. Enter the 4 or 5 digit code from above. After each code, try using the VOL UP and see if VOL works. If so, slide switch to AV1 or AV2 1. Press and hold MUTE and SELECT (LED flash 2x) 2. 993 then press SELECT NOTE: Be sure your Bose is set to accept the IR codes.
(Confirmed: works with BOSE Solo Soundbar with SKY HD Rev9, DirecTV RC64, and Xfinity remotes)
To program your remote control to a INSIGNIA Sound Bar, use the following codes: 21268 12002 10463
If using Comcast remote and above codes do not work, try Code Search: Turn on your sound bar. Press Aux once on remote. Then press and hold Setup until the key blinks 2x, then release Setup. Enter 9 – 9 – 3. The Aux key will blink 2x. Press Power and aim the remote control at the sound bar and press CH + one or more times until the sound bar turns off. Press Setup once to lock in the code. The Aux key will blink twice. To search for the codes of another device, repeat steps 1 to 5, but substitute the mode key for the device you are searching for. SIDE NOTE: In search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
(Confirmed: works with INSIGNIA Soundbar NS-SBAR-A, NS-SB314, SB212, with Comcast remotes)
To program your remote control to a SAMSUNG Sound Bar, use the following codes: 32609 22609 21014 20045
(Confirmed: works with Samsung Soundbar HW-FM55C, FM550, HW-HM45 and Xfinity remotes)
To program your remote control to a SONY Sound Bar, use the following codes: 1345 4029 31759
With Uverse remote try programming this method: Program = press ATT/OK at same time – 955 – Enter. In ATT mode set the STB sound to 15. Set TV sound to a comfortable level Set SONY soundbar sound to a comfortable level.
(Confirmed: works with SONY Soundbar HTCT260, CT770, CT-660, HTCT660 and Uverse remotes)
To program your remote control to an LG Sound Bar, use the following codes: 32676 11993 31953 31293
(Confirmed: works with LG Soundbar NB2022, NB3530A and Xfinity XR2 remote – Xfinity XR5 v4 remote)
To program your remote control to a VIZIO Sound Bar, use the following codes: 0883 0660 1517 1144 31517 11144 31975
Vizio Subwoofer volume control: 00105 Sub Down 00040 Sub Up
(Confirmed: works with VIZIO Soundbar VSB200, SB4020M-AO, SB15 2.1, VHT215, SB4021M-A1, VSB202, VSB210, VSB200-B)
Step-by-step for getting your Vizio Soundbar to work with the Comcast remote using EFC codes: Aux – Setup (2 blinks) – 11144 (2 blinks) Aux – Setup (2 blinks) – 994 – Setup – 001690 – Vol Up – 2 blinks Aux – Setup (2 blinks) – 994 – Setup – 001680 – Vol Down – 2 blinks Aux – Setup (2 blinks) – 994 – Setup – 000370 – Mute – 2 blinks Aux – Setup (2 blinks) – 994 – Setup – 001650 – Power – 2 blinks Aux – Setup (2 blinks) – 994 – Setup – 001640 – Input – 2 blinks
For Comcast remote, follow the Unlock/Lock directions using the 993 code to make the AUX Volume mode control the sound bar. Make sure you unlock the volume with the 993 code following the instructions. The Comcast remote will then control the volume via the sound bar and not the TV.
To program your remote control to a SANYO Sound Bar, use the following codes: 20047 10154 10159 10051 10250
When connecting the Sound Bar, you can plug your soundbar directly into the Cable box, SAT box, or TV. Different programming methods may be needed depending on how your soundbar is connected.
The above codes have shown to work with Sanyo soundbar models FWSB415E, FWSB405FS, FW405SB, and FWSB405F.
If these remote codes do not work, try the code search on your CAB or SAT remote…
ATT Remote RC7X: Program your Sanyo soundbar to the RC7x remote control: Follow the instructions by going to… -MENU -SETTINGS -SETTINGS & HELP -REMOTE CONTROL -AUDIO DEVICE
With DIRECTV or ATT as your cable with DIRECTV Remote Control: -Sanyo Soundbar on -Volume up but muted -AV1 or AV2 -Press and hold MUTE and SELECT for 2 blinks -Enter 9 9 1 and wait 2 blinks -Enter 3 -Press and release VOL UP -Point the remote at the Sanyo soundbar and keep pressing and releasing the CH UP key -When the volume changes, press select to lock in code.
If DIRECTV remote controls the power of the Sanyo soundbar but not volume, try this: -AV1 or AV2 -Press and hold MUTE & SELECT -Wait for 2 blinks and release -Enter 9 9 3 -Press SELECT
Code Search using silver Comcast remote with a red OK/Select button: -Turn on your Sanyo sound bar -Press Aux once -Press and hold Setup until the key blinks twice -Release Setup -Enter 9 9 1 3 -The Aux key will blink twice -Press Power and aim the remote control at the Sanyo sound bar -Press CH+ until the sound bar turns off NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device. -Press Setup once to lock in the code -The Aux key will blink twice
With a Comcast Xfinity remote with the red ok button: -Press aux then press and hold setup till it blinks twice -Enter code from list above (This code will control the volume)
With a Comcast Xfinity remote with the red ok button – To lock to the Sanyo soundbar: -Hold setup till it blinks twice -Enter 9 9 3 -Press aux To take the lock off and make it independent of each device: -Hold setup till it blinks twice -Press 993 then vol+ once (Now you can select each device you want to change the volume for)
The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Sanyo soundbar.
